ISO 17025 Certificate

ILAC-MRA.jpg head.jpg

PERRY JOHNSON LABORATORY
ACCREDITATION, INC.

Certificate of Accreditation

Perry Johnson Laboratory Accreditation, Inc. has assessed the Laboratory of:

Hammond Company
755 Larry Court, Waukesha, WI 53186

(Hereinafter called the Organization) and hereby declares that Organization is accredited in accordance with the recognized International Standard:

ISO/IEC 17025:2005

This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (as outlined by the joint ISO-ILAC-IAF Communique´ dated January 2009):

Calibration of Optical Comparators and Vision Systems
(As detailed in the supplement)

Accreditation claims for such testing and/or calibration services shall only be made from addresses referenced within this certificate. This accreditation is granted subject to the system rules governing the Accreditation referred to above, and the Organization hereby covenants with the Accreditation body’s duty to observe and comply with the said rules.

For PJLA:

signature.jpg
Tracy Szerszen
President/Operations Manager

 
Initial Accreditation Date:
November 20, 2003
Issue Date:
August 23, 20ll
Accreditation No.
59250
 Certificate No.
L11-134
Perry Johnson Laboratory
Accreditation, Inc. (PJLA)
755 W. Big Beaver, Suite 1325
Troy, Michigan 48084		 The validity of the certificate is maintained through ongoing assessments based
on a continuous accreditation cycle. The validity of this certificate should
be confirmed through the PJLA website www.pjlabs.com
ILAC-MRA.jpg head.jpg

Certificate of Accreditation: Supplement

Hammond Company

755 Larry Court, Waukesha, WI 53186
Tom Warzyn  Phone:262-798-4243 

Accreditation is granted to the facility to perform the following calibration:

Dimensional

MEASURED INSTRUMENT, QUANTITY OR GAUGE RANGE (AND SPECIFICATION WHERE APPROPRIATE) CALIBRATION AND MEASUREMENT CAPABILITTY EXPRESSED AS AN UNCERTAINTY  (±) CALIBRATION EQUIPMENT AND REFERENCE STANDARDS USED
Optical Comarator-Linear 0.010 in to 12 in
12 in to 24 in		 370 µin
440µin		 Glass Scale
Optical Comparator- Angular 1° to 360° 0.10° Reference Square
Squareness of
Y Axis to X Axis		 10 in of Y Axis travel or maximum Y travel if maximum is less than 10 in 171 µin Master Square
Optical Comparator- Magnification 10 X
20 X
31.25 X
50 X
62.5 X
100 X		 0.061%
0.043%
0.039%
0.034%
0.022%
0.017%		 Glass Scale
Vision System – Stage 6 in x 8 in
6 in x 10 in
6 in x 12 in
8 in x 8 in
12 in x 12 in
18 in x 18 in
188 in x 20 in
18 in x 24 in		 95 µin
110 µin
120 µin
100 µin
116 µin
180 µin
190 µin
214 µin		 Glass Grid
Vision System – Z axis 1 in to 4 in 71 µin Z Step Gage

The CMC (Calibration and Measurement Capability) stated for calibrations included on this scope of accreditation represent the smallest measurement uncertainties attainable by the laboratory when performing a more or less routing calibration of a nearly ideal device under nearly ideal conditions. It is expressed at a confidence level of 95% using a coverage factor k (usually equal to 2). The actual measurement uncertainty associated with a specific calibration performed by the laboratory will typically be larger than the CMC for same calibration since capability and performance of the device being calibrated and the conditions related to the calibration may reasonably be expected to deviate from ideal to some degree.

Issue: 8/11                     This supplement is in conjuction with certificate #L11-134